收藏我们   ENGLISH  
客服QQ
  点击这里给我发消息505255386
微信
  微信公共号
关键词查询
范围:  
提 交
《工程塑料应用》 2019年第10期
DOI:10.3969/j.issn.1001-3539.2019.10.014
工艺参数对SLA成型制件力学性能的影响
李晶晶1,马世博12,梁帅1,李韶臣1
1.河北科技大学材料科学与工程学院,石家庄 050018; 2.河北增材制造产业研究院,石家庄 050000 
Effect of Process Parameters on Mechanical Properties of SLA Molding Parts
Li Jingjing1, Ma Shibo12, Liang Shuai1, Li Shaochen1
1. College of Material Science and Engineering, Hebei University of Science and Technology, Shijiazhuang 050018, China; 2. Hebei Research Institute of Additional Materials Manufacturing Industry, Shijiazhuang 050000, China 
摘要:为了获得性能优异的立体光固化成型(SLA)制件,以SZUV-W8001P型光敏树脂为打印材料,基于SLA光固化3D打印机制备了不同工艺参数下的标准拉伸、弯曲及冲击试样,探究了打印层厚、填充扫描速度、填充线距及后固化时间等工艺参数对SLA成型试样力学性能的影响。结果表明,打印层厚为0.05 mm时,拉伸强度、弯曲强度和冲击强度均达到最大值,分别为48.52,68.63 MPa和174.76 kJ/m2;填充扫描速度对力学性能影响较小;力学性能随填充线距的增大呈先增大后减小的趋势,在0.04~0.06 mm时表现出良好的力学性能;拉伸强度随后固化时间的增加呈先上升后下降的趋势,后固化时间为100 min时拉伸强度最大为47.93 MPa;当打印层厚为0.05 mm,填充扫描速度为6000 mm/s,填充线距为0.04~0.06 mm以及后固化时间为100 min时,有利于SLA制件获得相对最优的力学性能。 
Abstract:Based on stereo lithography apparatus (SLA) curing technology, a series of standard tensile, bending and impact specimens were prepared by SZUV-W8001P photosensitive resin in order to obtain SLA parts with excellent properties. The effects of printing layer thickness, filling scanning speed, filling line distance and post-curing time on the mechanical properties of SLA samples were investigated. The results show that the tensile strength, bending strength and impact strength reach the maximum when the thickness of the printing layer is 0.05 mm, which are 48.52, 68.63 MPa and 174.76 kJ/m2 respectively. The filling scanning speed has little influence on the mechanical properties. The mechanical properties increase first and then decrease with the increase of filling line spacing, and show good mechanical properties at 0.04 - 0.06 mm. The tensile strength increases first and then decreases with post-curing time increasing, and the tensile strength is maximum at 47.93 MPa when the post-curing time is 100 min.When the thickness of printing layer is 0.05 mm, the filling scanning speed is 6000 mm/s, the filling line spacing is 0.04 - 0.06 mm and the post-curing time is 100 min, it is beneficial to obtain the relatively optimal mechanical properties of SLA parts. 
关键词:光敏树脂;打印参数;后固化时间;立体光固化成型;力学性能 
Keywords:photosensitive resin; printing parameter; post-curing time; stereo lithography apparatus molding; mechanical property 
基金:河北省增材制造产业技术研究院开放基金项目,河北省研究生创新项目(CXZZSS2017094) 
本文引用格式:
李晶晶,马世博,梁帅,等.工艺参数对SLA成型制件力学性能的影响[J].工程塑料应用,2019,47(10):75-79.
Li Jingjing,Ma Shibo,Liang Shuai,et al. Effect of process parameters on mechanical properties of SLA molding parts[J]. Engineering Plastics Application,2019,47(10):75-79. 

原文:
 
相似文章:
  交联剂DCP对PP/EPDM动态硫化热塑性弹性体影响
2020年第07期
  成型方法对PE-UHMW/PE-HD共混物流变行为和力学性能影响
2020年第07期
  增容剂种类对PC/ABS合金材料适用环境的影响
2020年第06期
  聚丙烯/硬脂酸锌/纳米氧化锌发泡材料的制备
2020年第06期
  二胺结构对聚亚胺vitrimer材料性能的影响
2020年第05期
  聚氨酯/无机填料复合材料制备及性能
2020年第04期
  热膨胀微球发泡剂对TPU泡沫结构与性能影响
2020年第04期
  丙烯基弹性体和乙烯-辛烯共聚物增韧聚丙烯性能
2020年第04期
  PE-HD/GNP/MWCNT纳米复合材料性能
2020年第04期
  MWCNT分布对POE/PA12复合材料性能影响
2020年第03期
《工程塑料应用》杂志社 版权所有,未经授权禁止复制或者建立镜像
地址:山东省济南市天桥区田庄东路3号 邮编:250031
电话:0531-85878057 85878223 85878278 传真:0531-85947355
鲁ICP备05018524号-5